F05/C5 control cable (Mercury/Mariner/MerCruiser) 9 feet (2,74 m) Riviera

C5-09' [Control cables F05/C5 · Riviera]
F05/C5 control cable (Mercury/Mariner/MerCruiser) 9 feet (2,74 m) Riviera

F05/C5 control cable (Mercury/Mariner/MerCruiser) 9 feet (2,74 m) Riviera. Before choosing, compare both end fittings, thread or mounting type, cable series, control, engine, year and required travel. Adapters may be required. The.

Read more
RRP46,77€VAT included
Offer price37,10€VAT included
Special offer
Available. Receive it between and Order by Friday 20 at 15:00 (Spain time).
Time remaining: 22:01:34
9/10 (2 votes)
Your opinion matters to us!
Thank you for your cooperation!
Votar:

Detailed description

Mechanical control cable for transmitting throttle or shift movement between the control lever and the engine in compatible installations.

Applications listed in the catalogue: Mercury, Mariner, MerCruiser; C5 / F05 type connections. Check the series, end fittings, travel and length of the installed cable. The engine brand alone does not confirm compatibility: the control and its connections must also match.

  • Series: Riviera F05 / C5
  • IMNASA reference: C5-09'
  • Length: 9 feet (2,74 m)
  • Travel: 95 mm
  • Outer casing diameter: 7 mm

Measure the entire route between the control and the engine, including the necessary bends. Install the cable without sharp bends or chafing and check the full throttle or shift movement before operating the boat.

Sold individually. Throttle and shift may require separate cables. Representative photograph of the series, shared across its different lengths.

How to choose and measure the cable

The order length is given in feet and its equivalent in metres. 1 foot = 0,3048 m: 9 feet = 2,7432 m (approx. 2,74 m). The metres shown are rounded to two decimal places; the nominal size identifying the reference is the length in feet.

To replace a Riviera or Ultraflex cable, the manufacturer specifies measuring the entire cable from tip to tip, including its ends, and checking the length marked on the casing. Do not measure only the outer casing section. If the previous installation was correct, do not add the allowance for engine steering movement to the old cable measurement again.

For a new installation, measure along the entire actual route from the control to the throttle or shift connection, including bends. For outboards, the catalogue diagram adds 3 feet (approx. 0,91 m) to allow for engine movement. For inboards and sterndrives, the A+B route is used. Choose the next available standard length that covers the required route and avoid excess cable and sharp bends.

Casing length, diameter and travel

The length of the outer casing, its diameter and the working travel are different measurements. For example, a casing diameter of 8,6 mm indicates its outside thickness; a travel of 80 mm indicates the usable movement of the end fitting. Neither value is the cable length. The separate casing length is not published for these references and is not calculated by subtracting the travel.

Before choosing, compare both end fittings, thread or mounting type, cable series, control, engine, year and required travel. Adapters may be required. Matching the engine brand and length alone does not guarantee a fit.

Customers who bought this product also purchased

Lubricante Quicksilver Con Teflon 2-4-C  236 ml
14,00€12,01€
Fastest delivery
Multiflex steering kit 09 Feet 6 mm H2
153,00€134,00€
Fastest delivery
Boat steering wheel Riviera Classic · 350 mm · black
45,21€33,11€
Fastest delivery
Black Outboard Remote Control CM01 Riviera
170,00€139,31€
Fastest delivery
Lalizas Anchorage Rope 10 mm 40 Meters
30,00€23,31€
Fastest delivery