Control cable F14/C14 (Johnson/Evinrude/OMC) 11 feet (3,35 m) Riviera

C14-11' [Control cables F14/C14 · Riviera]
Control cable F14/C14 (Johnson/Evinrude/OMC) 11 feet (3,35 m) Riviera

Control cable F14/C14 (Johnson/Evinrude/OMC) 11 feet (3,35 m) Riviera. Before choosing, compare both end fittings, thread or attachment type, cable series, control, engine, year and required travel. Adapters may be needed. The.

Read more
RRP47,60€VAT included
Offer price37,77€VAT included
Special offer
In stock. Immediate dispatch. Estimated delivery: Order by Friday 20 at 15:00 (Spain time).
Time remaining: 00:10:36
9/10 (2 votes)
Your opinion matters to us!
Thank you for your cooperation!
Votar:

Detailed description

Mechanical control cable for transmitting throttle or shift movement between the control lever and the engine in compatible installations.

Applications listed in the catalogue: Johnson, Evinrude and OMC, from 1979 onwards, with C14 / F14 connections. Check the series, end fittings, travel and length of the installed cable. The engine brand alone does not confirm compatibility: the control and its connections must also match.

  • Series: Riviera F14 / C14
  • IMNASA reference: C14-11'
  • Length: 11 feet (3,35 m)
  • Travel: 75 mm
  • Sheath diameter: 7 mm

Measure the entire route between the control and the engine, including the necessary bends. Install the cable without tight bends or chafing and check the full throttle or shift movement before using the boat.

Sold individually. The throttle and shift may require separate cables. Representative photograph of the series, shared across its different lengths.

How to choose and measure the cable

The order length is stated in feet with its equivalent in metres. 1 foot = 0,3048 m: 9 feet = 2,7432 m (approx. 2,74 m). The metres shown are rounded to two decimal places; the commercial size identifying the reference is the length in feet.

When replacing a Riviera or Ultraflex cable, the manufacturer instructs you to measure the complete cable from tip to tip, including its ends, and check the length marked on the sheath. Do not measure only the outer sheath section. If the previous installation was correct, do not add the allowance for engine turning again to the old cable measurement.

For a new installation, measure along the entire actual route from the control to the throttle or shift connection, including bends. For outboards, the catalogue diagram adds 3 feet (approx. 0,91 m) to allow engine movement. For inboards and sterndrives, the A+B route is used. Choose the next available commercial length that covers the required route and avoid excess cable and tight bends.

Sheath length, diameter and travel

The outer sheath length, its diameter and the working travel are different measurements. For example, a sheath diameter of 8,6 mm indicates its outside thickness; a travel of 80 mm indicates the usable movement of the end fitting. Neither value is the cable length. The separate sheath length is not published for these references and is not calculated by subtracting the travel.

Before choosing, compare both end fittings, thread or attachment type, cable series, control, engine, year and required travel. Adapters may be needed. Matching the engine brand and length alone does not guarantee a fit.

Customers who bought this product also purchased

IMNASA K23 Cable Connection Kit
26,68€24,98€
Fastest delivery between and
Spanish flag with crown 30×20 cm
2,50€2,50€
Fastest delivery
Swivel hasp · 91 × 29 mm · Stainless steel 316
7,00€4,23€
Fastest delivery
Ocean Bay A0 red round fender Ø210 × 280 mm
20,00€15,00€
Fastest delivery